{
 "slug": "hp-elitebook-830-g5-rtc-battery",
 "title": "How to do an HP EliteBook 830 G5 RTC battery replacement",
 "model": "hp-elitebook-830-g5",
 "model_name": "HP EliteBook 830 G5",
 "component": "rtc-battery",
 "manufacturer": "HP",
 "url": "https://laptoppartfinder.com/guides/hp-elitebook-830-g5-rtc-battery/",
 "api_url": "https://laptoppartfinder.com/api/guides/hp-elitebook-830-g5-rtc-battery",
 "source_url": "https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf",
 "source_title": "HP Maintenance and Service Guide",
 "pages": "printed pages 34, 36, 38–41, 56",
 "service_classification": null,
 "bench_tested": false,
 "markdown": "# HP EliteBook 830 G5 RTC battery replacement\n\nSource: https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf (printed pages 34, 36, 38–41, 56). OEM-documented procedure; not bench-tested.\n\nReplace the OEM cabled RTC battery assembly as an intact service pack; no internal-cell dismantling or polarity/connector conversion.\n\nRTC is in the authorized service provider chapter; target access/replacement is ASP-only. [HP printed 38, PDF 48](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=48); [HP printed 53, PDF 63](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=63)\n\n## Assembly inventory and configuration\n\nL13694-001 is the listed RTC battery assembly for this exact model. A shared spare in another model is not blanket compatibility evidence. [HP printed 24, PDF 34](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=34); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\nExact HP EliteBook 830 G5 and a verified like-for-like OEM assembly/configuration; preserve original routing and connector identity. Serial fit and regional eligibility remain unverified. Other models/generations, arbitrary substitutions and upgrades. No bare-cell substitution, pack dismantling, lead/polarity conversion, charging a primary cell or CMOS/password/firmware changes. [HP printed 24, PDF 34](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=34); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\nPhillips P0; flat case/RTC release tool; grounded ESD workstation/strap. A nonconductive/nonmarking flat tool is an editorial selection where the RTC section says only flat tool. [HP printed 33, PDF 43](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=43); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\n- **L13694-001**: RTC battery assembly. Role: target assembly. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\n## Documented facts and proposed boundaries\n\nThe documented service unit has a cable/plug and is removed intact. The procedure does not authorize opening its wrap, replacing an internal CR2032-like cell, changing lead polarity or attaching a generic coin cell. Basis: DOCUMENTED assembly/connector scope; PROPOSED substitution boundary. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\nThe illustrated RTC plug connects to the system board (callout 1); the tool release is callout 2 and pack lift is callout 3. The manual calls the seat a holder and uses a flat tool to pry the pack free. Basis: DOCUMENTED OEM text and applicable figure. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\nNo keyboard, radio antenna, speaker assembly, system-board or thermal-interface removal is an RTC prerequisite. Only the main-battery cable is disconnected; the main pack and its screws remain installed. Basis: DOCUMENTED OEM text and applicable figure. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 40, PDF 50](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=50)\n\n## Ordered replacement procedure\n\n1. **prepare** - Save work and shut down through the operating system. If power/hibernation state is uncertain, start normally and then shut down. Disconnect external devices and AC power before opening. Use a flat ESD-protected grounded work surface with a grounded wrist strap; avoid pins and circuitry and keep screws organized. Basis: DOCUMENTED shutdown/ESD precautions; PROPOSED organization join. [HP printed 38, PDF 48](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=48); [HP printed 36, PDF 46](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=46)\n\n2. **access** - Turn the computer upside down. Loosen five ordinary captive screws and two inset captive screws (seven total). Starting under the display, use the case removal tool to release and lift off the bottom cover. Basis: DOCUMENTED OEM operation paraphrased. [HP printed 38, PDF 48](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=48); [HP printed 39, PDF 49](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=49)\n\n3. **isolate** - Disconnect the main-battery cable at the system board, handling the connector rather than pulling its wires. Leave the battery pack and its retention screws installed: this target procedure calls for cable isolation only. Basis: DOCUMENTED OEM operation paraphrased. [HP printed 40, PDF 50](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=50)\n\n4. **disconnect** - Disconnect the RTC pack cable from its system-board socket (RTC figure callout 1), handling its plug rather than pulling on the wires. This is separate from the already isolated main battery. Basis: DOCUMENTED OEM operation paraphrased. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 34, PDF 44](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=44)\n\n5. **remove** - Use the flat tool at the holder’s illustrated release point (callout 2), free the intact RTC pack from the holder and lift it out at callout 3. Keep the pack, lead and connector together. Basis: DOCUMENTED OEM operation paraphrased. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\n6. **install** - Seat the matching L13694-001 intact RTC assembly in its original holder/recess and orientation by reversing removal. Keep its existing connector/lead arrangement; do not dismantle the pack or infer loose-cell polarity from the drawing. No RTC retaining screw, added adhesive type or torque is specified here. Basis: DOCUMENTED reverse installation expanded; PROPOSED intact-pack boundary. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66)\n\n7. **reconnect** - Route the RTC lead as originally installed and reconnect its matching plug to the system-board socket. Check that the pack is retained and the lead is clear of surrounding hardware without pulling, twisting or trapping it. Basis: DOCUMENTED reverse connection/cable-care rule; PROPOSED retention/routing check. [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 56, PDF 66](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=66); [HP printed 34, PDF 44](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=44)\n\n8. **restore** - After checking target retention, connectors and cable routing and removing loose hardware, reconnect the main-battery cable to the system board. The main battery has not been removed. Basis: DOCUMENTED reverse battery procedure; PROPOSED inspection join. [HP printed 40, PDF 50](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=50); [HP printed 41, PDF 51](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=51)\n\n9. **close** - Refit the bottom cover, engage its original edges and tighten its seven captive screws in their original locations. Reconnect external devices and AC only after the enclosure is secured. Basis: DOCUMENTED reverse-cover procedure; PROPOSED closed-unit restoration join. [HP printed 38, PDF 48](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=48); [HP printed 39, PDF 49](https://h10032.www1.hp.com/ctg/Manual/c06189588.pdf#page=49)\n\n## Proposed checks and limits\n\nUNPERFORMED PROPOSED editorial check after correct complete reassembly: observe ordinary closed-unit startup and the displayed date/time without changing firmware settings. This is not a replacement interval, diagnosis or password-reset claim.\n"
}