{
 "slug": "hp-probook-455-g3-display-assembly-replacement-p75",
 "title": "How to do an HP ProBook 455 G3 display assembly replacement",
 "model": "hp-probook-455-g3",
 "model_name": "HP ProBook 455 G3",
 "component": "display assembly",
 "manufacturer": "HP",
 "url": "https://laptoppartfinder.com/guides/hp-probook-455-g3-display-assembly-replacement-p75/",
 "api_url": "https://laptoppartfinder.com/api/guides/hp-probook-455-g3-display-assembly-replacement-p75",
 "source_url": "https://h10032.www1.hp.com/ctg/Manual/c04825528.pdf",
 "source_title": "HP Maintenance and Service Guide",
 "pages": "printed pages 75–79",
 "service_classification": null,
 "bench_tested": false,
 "markdown": "# HP ProBook 455 G3 display assembly replacement\n\nSource: https://h10032.www1.hp.com/ctg/Manual/c04825528.pdf (printed pages 75–79). OEM-documented procedure; not bench-tested.\n\nHP ProBook 455 G3 Notebook PC display assembly replacement. HP prints this procedure on printed page 75 of its maintenance and service guide.\n\n## Tools and parts\n\n- Screwdrivers and a non-marking pry tool as HP lists for this procedure\n- Static-safe work surface\n\n## Preparation\n\nSave your work and shut the computer down through the operating system, unplug AC power and every external device, and work on a clean, grounded, ESD-protected surface while sorting each screw by its original location. Handle every cable by its connector and put each one back in its own place during reassembly.\n\n## Replacement\n\n1. Position the computer upright and open. (printed page 75).\n2. Detach the display cable from the system board (1). (printed page 75).\n3. Pull the antennas through the hole in the machine (2), and after that take them away from the routing path near the right screen hinge (3). (printed page 75).\n4. Take out the 5 Phillips PM2.5×5.0 screws from the display hinges. (printed page 75).\n5. Lift the display assembly straight up (printed page 76).\n6. To remove the display bezel (printed page 76).\n7. Flex the top of the bezel (printed page 76).\n8. Take out the display bezel (4). (printed page 77).\n9. If it is needed to substitute the webcam or microphone unit, disconnect the cable from the module (printed page 77).\n10. If it is necessary to take the screen panel from the enclosure, take the 4 Phillips PM2.0×3.0 fasteners that hold the panel to the screen enclosure. (printed page 78).\n11. Turn the screen panel all the way over (1), and after that lift the tape off the top of the connector (2) and detach the lead from the rear of the panel (3). (printed page 78).\n12. Take out the display panel from the enclosure. (printed page 78).\n13. If it is necessary to replace the screen hinges, take the 2 Phillips PM2.0×3.0 fasteners at the top (1) as well as the 4 broadhead Phillips PM2.5×3.0 fasteners at the bottom (2) that hold the screen hinges to the screen enclosure. (printed page 78).\n14. Take out the display hinges from the display enclosure (3). (printed page 79).\n15. If it is necessary to replace the screen lead, take the lead from the clips integrated into the left side of the screen enclosure (1). (printed page 79).\n16. Lift the cable off the display enclosure (2). (printed page 79).\n17. Fit the replacement part by working back through the printed removal steps (printed page 79).\n",
 "outcome": "found",
 "data_revision": "93b6f8041cad",
 "license": "Free to use with attribution: credit \"Laptop Part Finder\" and link to https://laptoppartfinder.com (or the page you used). Please do not republish or mirror the dataset in bulk without permission.",
 "attribution": "Laptop Part Finder (https://laptoppartfinder.com)",
 "terms_url": "https://laptoppartfinder.com/terms/#data-license"
}