HP EliteBook x360 830 G6 battery replacement

Step-by-step HP EliteBook x360 830 G6 battery replacement paraphrased from HP's official Maintenance and Service Guide, with page citations.

Source: paraphrased from HP's official Maintenance and Service Guide (PDF, printed pages 29–37). Not bench-tested. We have not performed this repair; keep HP's manual open for its illustrations. Scope restrictions below are part of the guide: do not apply it to other models, generations or configurations. Service manuals are written for trained technicians; work at your own risk.
HP service classification: Customer Self-Repair chapter; regional/warranty eligibility must be checked; not blanket authorization.

Labels: DOCUMENTED = taken from HP's manual; PROPOSED = our own joining or ordering of HP's directions, not an HP instruction; UNPERFORMED = a suggested check that has not been carried out.

Applies to

HP EliteBook x360 830 G6. Confirm the exact model on the service label before starting.

Service classification: Customer Self-Repair chapter; regional/warranty eligibility must be checked; not blanket authorization. HP manual, printed 34 / PDF 44

Scope: Replaceable battery in exact convertible model.

Applicability and parts

  • Exact x360 830 G6 convertible; no clamshell 830 substitution.

DOCUMENTED manual table options follow. A table entry is not serial-specific fit, present availability, upgrade approval or a shopping recommendation. Check the actual product/configuration before selecting a spare.

SpareDocumented description / constraintEvidence
L34449-0024-cell, 53 Whr, 3.45 Ahr battery including cable; documented option; verify exact product/configurationHP manual, printed 37 / PDF 47

Tools and handling

  • Torx T5 driver for cover
  • Phillips P0/P1 driver appropriate to screw head
  • nonconductive nonmarking pry tool
  • ESD protection and screw organizer

The model-specific preparation and handling citations are included in the first step. Use the correct driver for the actual head. Do not borrow screw, Battery Safe, keyboard-cable or memory-slot rules from another HP model.

Ordered procedure

DOCUMENTED steps paraphrase HP. Reassembly expands HP’s reverse-procedure directions. Any combined order identified as PROPOSED is our own synthesis of those directions, not a separate HP or bench-verified instruction. No numeric torque or unprovided latch motion is added.

  1. Prepare. Confirm the exact model/product label and matching replacement configuration before opening. Shut down through the operating system (wake and shut down if uncertain about sleep/hibernation); unplug external devices and AC power. Work on a clean ESD-protected surface with grounded handling precautions; handle boards/modules by edges, keep liquids away, and sort screws by original location. Do not bend, crush, puncture or use a sharp tool against a battery. Stop for a swollen/damaged pack or a hardware/connector mismatch. (DOCUMENTED) HP manual, printed 34 / PDF 44; HP manual, printed 29 / PDF 39; HP manual, printed 30 / PDF 40; HP manual, printed 31 / PDF 41; HP manual, printed 32 / PDF 42; HP manual, printed 33 / PDF 43
  2. Access. With the closed computer supported upside down, loosen five captive Torx T5 screws. Release at the hinges, rotate the hinge-side edge upward, and lift off the cover. Keep each fastener at its original location; do not detach captive screws. (DOCUMENTED) HP manual, printed 35 / PDF 45; HP manual, printed 36 / PDF 46
  3. Isolate. Disconnect the battery cable from the system board by its connector; do not pull its wires. Remove the five Phillips M2.0 × 3.5 battery screws and lift out the battery. Store it safely. (DOCUMENTED) HP manual, printed 37 / PDF 47
  4. Remove. Compare replacement pack, cable and mounting points with the removed pack and documented option before installing. Do not transfer an unlisted clamshell battery into this convertible. (DOCUMENTED) HP manual, printed 37 / PDF 47
  5. Install. Place the replacement battery in its original position and restore the five Phillips M2.0 × 3.5 screws. Reconnect its system-board cable after confirming that the cable is clear of pinching. (DOCUMENTED reverse-procedure direction) HP manual, printed 37 / PDF 47
  6. Close. Check that every cable is seated and routed clear of the cover and that no screw/tool remains inside. Refit and seat the bottom cover, engaging its clips; restore five captive Torx T5 screws to their original holes. No numerical torque is supplied here. (PROPOSED combined reassembly order, following OEM reverse-procedure directions) HP manual, printed 35 / PDF 45; HP manual, printed 36 / PDF 46

Proposed checks — all unperformed

  • UNPERFORMED: reconnect AC only after the cover is fitted; power on and check for startup/charging errors. Check battery recognition and charging behavior.
  • UNPERFORMED: if a fault appears, shut down and isolate power before any internal inspection.

Part numbers in our catalog

Check each part page for its source and variant notes before ordering.

Official manual

HP Maintenance and Service Guide (PDF, HP). Machine-readable copy: /api/guides/hp-elitebook-x360-830-g6-battery-replacement