HP EliteBook x360 830 G6 SSD replacement

Labels: DOCUMENTED = taken from HP's manual; PROPOSED = our own joining or ordering of HP's directions, not an HP instruction; UNPERFORMED = a suggested check that has not been carried out.

Applies to

HP EliteBook x360 830 G6. Confirm the exact model on the service label before starting.

Service classification: Customer Self-Repair chapter; regional/warranty eligibility must be checked; not blanket authorization. HP manual, printed 34 / PDF 44

Scope: Replaceable ssd in exact convertible model.

Applicability and parts

• Exact x360 830 G6; table options are not approval for protocol, encryption, capacity or Xpoint conversion. Backup/recovery and software migration are outside the mechanical procedure.

DOCUMENTED manual table options follow. A table entry is not serial-specific fit, present availability, upgrade approval or a shopping recommendation. Check the actual product/configuration before selecting a spare.

Tools and handling

• Torx T5 driver for cover
• Phillips P0/P1 driver appropriate to screw head
• nonconductive nonmarking pry tool
• ESD protection and screw organizer

The model-specific preparation and handling citations are included in the first step. Use the correct driver for the actual head. Do not borrow screw, Battery Safe, keyboard-cable or memory-slot rules from another HP model.

Ordered procedure

DOCUMENTED steps paraphrase HP. Reassembly expands HP’s reverse-procedure directions. Any combined order identified as PROPOSED is our own synthesis of those directions, not a separate HP or bench-verified instruction. No numeric torque or unprovided latch motion is added.

1. Prepare. Confirm the exact model/product label and matching replacement configuration before opening. Shut down through the operating system (wake and shut down if uncertain about sleep/hibernation); unplug external devices and AC power. Work on a clean ESD-protected surface with grounded handling precautions; handle boards/modules by edges, keep liquids away, and sort screws by original location. Do not bend, crush, puncture or use a sharp tool against a battery. Stop for a swollen/damaged pack or a hardware/connector mismatch. (DOCUMENTED) HP manual, printed 34 / PDF 44; HP manual, printed 29 / PDF 39; HP manual, printed 30 / PDF 40; HP manual, printed 31 / PDF 41; HP manual, printed 32 / PDF 42; HP manual, printed 33 / PDF 43
2. Access. With the closed computer supported upside down, loosen five captive Torx T5 screws. Release at the hinges, rotate the hinge-side edge upward, and lift off the cover. Keep each fastener at its original location; do not detach captive screws. (DOCUMENTED) HP manual, printed 35 / PDF 45; HP manual, printed 36 / PDF 46
3. Isolate. Disconnect the battery cable from the system board by its connector; do not pull its wires. Remove the five Phillips M2.0 × 3.5 battery screws and lift out the battery. Store it safely. (DOCUMENTED) HP manual, printed 37 / PDF 47
4. Remove. Release and remove the SSD shield from its board clips without bending it or disturbing neighboring components. Keep it for reuse. (DOCUMENTED) HP manual, printed 42 / PDF 52
5. Remove. Remove the single Phillips M2.0 × 2.0 SSD retaining screw. Withdraw the module from the socket by its edges; do not force the keyed connection. (DOCUMENTED) HP manual, printed 43 / PDF 53
6. Install. Insert the correctly matched replacement into the keyed socket, return it to its original position and restore the single Phillips M2.0 × 2.0 screw. Refit the SSD shield into the board clips; it must be secured, not merely laid on top. (DOCUMENTED reverse-procedure direction and explicit shield tip) HP manual, printed 42 / PDF 52; HP manual, printed 43 / PDF 53
7. Restore. After all component/shield work and internal checks, position the battery and restore its five Phillips M2.0 × 3.5 screws, then reconnect the battery cable to the system board. Keep the cable clear of the cover. (PROPOSED combined reassembly order, using OEM reverse direction) HP manual, printed 37 / PDF 47
8. Close. Check that every cable is seated and routed clear of the cover and that no screw/tool remains inside. Refit and seat the bottom cover, engaging its clips; restore five captive Torx T5 screws to their original holes. No numerical torque is supplied here. (PROPOSED combined reassembly order, following OEM reverse-procedure directions) HP manual, printed 35 / PDF 45; HP manual, printed 36 / PDF 46

Proposed checks — all unperformed

• UNPERFORMED: reconnect AC only after the cover is fitted; power on and check for startup/charging errors. Check firmware drive detection; use the owner’s prepared recovery/boot method. Data migration, encryption recovery and bootability have not been tested.
• UNPERFORMED: if a fault appears, shut down and isolate power before any internal inspection.

Official manual

HP Maintenance and Service Guide (PDF, HP). Machine-readable copy: /api/guides/hp-elitebook-x360-830-g6-ssd-replacement