HP ProBook 470 G3 display assembly replacement

Step-by-step HP ProBook 470 G3 display assembly replacement rewritten in our own words from HP's Maintenance and Service Guide, with page citations.

Part you need827046-001HP 17.3-inch display panel 827046-001 for the HP ProBook 470 G3
View part & buy links
On this page
  1. Applies to
  2. Tools and parts
  3. Preparation
  4. Replacement
  5. Part numbers in our catalog
  6. Manufacturer manual
Source: steps rewritten in our own words (no more than 8 words in a row copied; part numbers, screw sizes and warnings kept as printed) from HP's Maintenance and Service Guide (PDF, printed pages 77–82). Not bench-tested. We have not performed this repair; keep HP's manual open for its illustrations. Scope restrictions below are part of the guide: do not apply it to other models, generations or configurations. Service manuals are written for trained technicians; work at your own risk.

Labels: DOCUMENTED = taken from HP's manual; PROPOSED = our own joining or ordering of HP's directions, not an HP instruction; UNPERFORMED = a suggested check that has not been carried out.

Applies to

HP ProBook 470 G3. Confirm the exact model on the service label before starting.

HP ProBook 470 G3 Notebook PC display assembly replacement. HP prints this procedure on printed page 77 of its maintenance and service guide.

Tools and parts

  • Screwdrivers and a non-marking pry tool as HP lists for this procedure
  • Static-safe work surface

Preparation

Save your work and shut the computer down through the operating system, unplug AC power and every external device, and work on a clean, grounded, ESD-protected surface while sorting each screw by its original location. Handle every cable by its connector and put each one back in its own place during reassembly.

Replacement

  1. Position the computer upright and open. (printed page 77).
  2. Detach the display cable from the system board (1). (printed page 77).
  3. Pull the WLAN antennas across the hole in the computer (2). (printed page 77).
  4. Take out the 5 Phillips PM2.5×5.0 screws from the display hinges. (printed page 77).
  5. Lift the display assembly straight up (printed page 78).
  6. To remove the display bezel (printed page 78).
  7. Flex the top of the bezel (printed page 78).
  8. Take out the display bezel (6). (printed page 79).
  9. If it is needed to substitute the webcam or microphone unit, disconnect the cable from the module (printed page 79).
  10. If it is necessary to take the screen panel from the enclosure, take the 4 Phillips PM2.0×3.0 (printed page 80).
  11. Lift the display cable connector clip (1) (printed page 80).
  12. Take out the display panel from the enclosure. (printed page 80).
  13. If it is necessary to replace the screen hinges, take the 2 Phillips PM2.0×3.0 fasteners at the top (1) and (printed page 81).
  14. Take out the display hinges from the display enclosure (3). (printed page 81).
  15. If it is necessary to replace the screen/webcam lead, lift the webcam lead to disengage the adhesive (printed page 81).
  16. Raise the tabs to disengage the adhesive on the lead near the bottom of the screen enclosure (3), and (printed page 82).
  17. Fit the replacement part by working back through the printed removal steps (printed page 82).

Part numbers in our catalog

Check each part page for its source and variant notes before ordering.

Manufacturer manual

HP Maintenance and Service Guide (PDF, HP). Machine-readable copy: /api/guides/hp-probook-470-g3-display-assembly-replacement-p77

Key facts

HP document part number
824661-001
Model
HP ProBook 470 G3
Release year
2015
Screen size
17.3"
Printed pages
77–82

Related