HP Fortis Flip G1m 11 inch Chromebook display assembly replacement

Labels: DOCUMENTED = taken from HP's manual; PROPOSED = our own joining or ordering of HP's directions, not an HP instruction; UNPERFORMED = a suggested check that has not been carried out.

Applies to

HP Fortis Flip G1m 11 inch Chromebook. Confirm the exact model on the service label before starting.

HP Fortis Flip G1m 11 inch Chromebook display assembly replacement. HP prints this procedure on printed page 48 of its maintenance and service guide.

tools and parts

• Tweezers, Nonconductive, nonmarking pry tool and Magnetic Phillips P1 drivers
• Static-safe work surface
• No spare part number for this component was found in the cached manual

preparation

HP prints its tools list and its handling and electrostatic-discharge cautions on printed page 17. Its preparation for disassembly is on printed page 26: power the unit down through the operating system, unplug the power cord and detach every external device before opening it. Work on a grounded, static-safe surface, keep screws grouped by the position they came from, and handle boards and modules by their edges.

replacement

1. Take out the plastic antenna protector from the WLAN module. (printed page 48).
2. Detach the antenna cables from the WLAN module. (printed page 48).
3. Take out the antenna cables from the clips along the upper of the computer. (printed page 48).
4. Detach touch cable from system board, and then remove cable from the clips along the top of the computer. (printed page 48).
5. Detach display cable from ZIF connector on the system board. (printed page 48).
6. Take out the display cable from the clips along the top of the computer. (printed page 48).
7. Take out the six Phillips M2.5 × 3.5 screws that hold the display assembly to the computer. (printed page 48).
8. Swing the display open to 90° (1), and then separate the display from the computer. (printed page 49).
9. To remove display panel from display assembly: a. Use tool or your fingers to separate top of panel from display rear cover. b. Lift top of the panel up. c. Rotate the panel over next to the display rear cover. (printed page 49).
10. To remove touch control board from bottom of display panel: a. Peel tape off board. b. Detach two cables from reverse ZIF connectors on the board. c. Take out the board from the panel. (printed page 50).
11. To remove display brackets from the display rear cover: a. Take out the two Phillips M2.5 × 3.0 screws from each hinge. b. Take out the Phillips M2.0 × 2.5 screw from the top of each bracket. (printed page 50).
12. To remove hinges from the display rear cover: a. Take out the Phillips M2.5 × 2.5 broad head screw from each hinge. b. Rotate the hinges to the closed position. c. Take out the rubber stoppers from each hinge. (printed page 51).
13. To remove camera module: a. Lift cable off upper of connector on camera module. b. Detach cable from the ZIF connector on the module. c. (printed page 52).
14. To remove display/camera cable: a. Detach cable from ZIF connector on camera module. b. Peel cable off the inside of the display rear panel. c. Take out the rubber stopper from the left hinge. (printed page 52).
15. To remove WLAN antennas and cables, release cables from clips along upper and side on display rear cover, and then peel antennas off the cover. (printed page 53).

Part numbers in our catalog

• HP 11.6-inch display panel P22926-001 (P22926-001)
• HP Screen P22930-001 (P22930-001)

Check each part page for its source and variant notes before ordering.

Manufacturer manual

HP Maintenance and Service Guide (PDF, HP). Machine-readable copy: /api/guides/hp-fortis-flip-g1m-11-inch-chromebook-display-assembly-replacement-p48