HP EliteBook 1040 G11 display assembly replacement

Step-by-step HP EliteBook 1040 G11 display assembly replacement rewritten in our own words from HP's Maintenance and Service Guide, with page citations.

Part you needN98107-001HP 14-inch OLED 400 nit non-touch, IR webcam, WLAN models display assembly for the HP EliteBook 1040 G11
View part & buy links
On this page
  1. Applies to
  2. Tools and parts
  3. Preparation
  4. Replacement
  5. Part numbers in our catalog
  6. Manufacturer manual
Source: steps rewritten in our own words (no more than 8 words in a row copied; part numbers, screw sizes and warnings kept as printed) from HP's Maintenance and Service Guide (PDF, printed pages 60–62). Not bench-tested. We have not performed this repair; keep HP's manual open for its illustrations. Scope restrictions below are part of the guide: do not apply it to other models, generations or configurations. Service manuals are written for trained technicians; work at your own risk.

Labels: DOCUMENTED = taken from HP's manual; PROPOSED = our own joining or ordering of HP's directions, not an HP instruction; UNPERFORMED = a suggested check that has not been carried out.

Applies to

HP EliteBook 1040 G11. Confirm the exact model on the service label before starting.

HP Elitebook 1040 14 inch G11 Notebook display assembly replacement. HP prints this procedure on printed page 60 of its maintenance and service guide.

Tools and parts

  • Screwdrivers and a non-marking pry tool as HP lists for this procedure
  • Static-safe work surface
  • N98107-001 - 35.6 cm (14.0 in), brightview, UWVA, OLED + LBL, nTOP, with infrared webcam, for use on computer models equipped with WLAN; typical brightness: 400 nits. Source: printed page 60.
  • P04250-001 - 35.6 cm (14.0 in), antiglare, WUXGA, TOP, with privacy filter and infrared webcam, for use on computer models equipped with WWAN; typical brightness: 800 nits. Source: printed page 60.
  • N98103-001 - 35.6 cm (14.0 in), antiglare, WUXGA, TOP, with TOF infrared webcam, for use on computer models equipped with WWAN; typical brightness: 400 nits. Source: printed page 60.
  • N98102-001 - 35.6 cm (14.0 in), antiglare, WUXGA, TOP, with TOF infrared webcam, for use on computer models equipped with WLAN; typical brightness: 400 nits. Source: printed page 60.
  • N98106-001 - 35.6 cm (14.0 in), antiglare, WUXGA, nTOP, WLED + LBL, with infrared webcam, for use on computer models equipped with WWAN; typical brightness: 400 nits. Source: printed page 60.
  • N98105-001 - 35.6 cm (14.0 in), antiglare, WUXGA, nTOP, WLED + LBL, with infrared webcam, for use on computer models equipped with WLAN; typical brightness: 400 nits. Source: printed page 60.
  • N98104-001 - 35.6 cm (14.0 in), antiglare, WUXGA, nTOP, with privacy filter and infrared webcam, for use on computer models equipped with WWAN; typical brightness: 1000 nits. Source: printed page 60.
  • N98503-001 - 35.6 cm (14.0 in), antiglare, WUXGA, nTOP, with infrared webcam, for use on computer models equipped with WWAN; typical brightness: 800 nits. Source: printed page 60.

Preparation

Save your work and shut the computer down through the operating system, unplug AC power and every external device, and work on a clean, grounded, ESD-protected surface while sorting each screw by its original location. Handle every cable by its connector and put each one back in its own place during reassembly.

Replacement

  1. Detach the display hub cable from the system board. (printed page 60).
  2. Gently detach the two WWAN antenna cables from the terminals on the WWAN module. (printed page 60).
  3. Let go of the WWAN antenna cables from the retention clips and routing channels that are built (printed page 61).
  4. Detach the display panel cable from the system board. (printed page 61).
  5. Gently detach the two WLAN antenna cables from the terminals on the WLAN module. (printed page 61).
  6. Let go of the WLAN antenna cables from the retention clips and routing channels that are built (printed page 61).
  7. Take out the six Phillips M2.5 × 4.1 screws that hold the display assembly to the computer. (printed page 62).
  8. Swing the top edge of the display assembly down and away from the top panel with keyboard (printed page 62).
  9. Let go of the display hinges from the top panel by sliding the top cover with keyboard away from (printed page 62).
  10. Separate the top cover with keyboard from the display assembly. (printed page 62).

Part numbers in our catalog

Check each part page for its source and variant notes before ordering.

Manufacturer manual

HP Maintenance and Service Guide (PDF, HP). Machine-readable copy: /api/guides/hp-elitebook-1040-14-inch-g11-notebook-display-assembly-replacement-p60

Key facts

HP document part number
N99985-002
Model
HP EliteBook 1040 G11
Release year
2024
Screen size
14"
Printed pages
60–62